Product Introduction
◎Infrared human body sensing system: Adopting microwave radar + PIR dual-mode technology, it achieves 0.5-second response and 5-level delayed shutdown, with an energy-saving rate of 65%, suitable for scenarios such as expressway service areas and border patrols.
◎Advanced heat dissipation technology: Through 3D microchannel substrates, fractal plume fins and phase change materials, the junction temperature is reduced by 20.5%, the light decay rate is reduced to 5%, supporting extreme environments from -50℃ to +80℃.
◎Comprehensive performance comparison: The system has a luminous efficiency of 175lm/W, IP65 protection, and a MTBF of 50,000 hours. Compared with ordinary products, the battery life is extended by 2 days, and the failure rate is reduced by 50%.

Infrared Human Body Sensing System
Technical Architecture and Core Parameters
The product adopts microwave radar + pyroelectric infrared (PIR) dual-mode sensing technology. It focuses the 9-10μm wavelength infrared rays emitted by the human body onto the sensor's sensitive element through a Fresnel lens. The triggered signal is processed by a low-noise amplifier (gain ≥70dB) to drive the LED light source, achieving an ultra-fast 0.5-second response and 5-level delayed shutdown (adjustable from 30 seconds to 30 minutes).
◎Intelligent light control module: Built-in photoresistor automatically locks the sensing function when ambient illuminance >50lux to avoid false triggers during the day;
◎Anti-interference algorithm: Filters non-human movement signals such as pets and swaying leaves through dynamic threshold adjustment technology, with a false trigger rate <0.3%;
◎Multi-target recognition: Supports simultaneous tracking of 3 moving targets, with a sensing range covering a circular area with a diameter of 12 meters (when installed at 8 meters height).

Expansion of Application Scenarios
◎Expressway service areas: Through linkage between buried sensors and street lights, the lights automatically turn on when vehicles enter a 50-meter range and turn off 30 seconds after leaving, solving the problem of "waste from constant lighting" of traditional street lights;
◎Border patrol roads: In unattended areas, the sensing system can link with cameras to start recording, realizing the dual functions of "lighting + security";
◎Polar research stations: In -40℃ low-temperature environments, cold-resistant PIR sensors (operating temperature range -50℃ to +80℃) are used to ensure that sensing sensitivity does not attenuate.
Advanced Heat Dissipation Technology
◎3D microchannel heat dissipation substrate: Copper tubes (outer diameter 8mm) are embedded into the 6063-T5 aluminum alloy base through laser welding technology to form a three-dimensional water-cooled circulation channel, with heat conduction efficiency 300% higher than that of ordinary aluminum substrates;
◎Fractal plume heat dissipation fins: Imitating the natural convection form of melting iceberg snow, 12 groups of gradient fins are generated through parametric design. The fin spacing gradually expands from 3mm at the bottom to 8mm at the top, reducing wind resistance (Cd value 0.32) while expanding the heat dissipation area from 0.45㎡ to 0.68㎡;
◎Phase change material filling: Graphene composite phase change material (melting point 58℃) is injected between the chip and the substrate. When the junction temperature exceeds the threshold, the material changes from solid to liquid to absorb heat, delaying thermal runaway for up to 15 minutes.
Experimental Data Comparison
Under extreme conditions of 45℃ ambient temperature and 120W full-power operation:
|
Test Item |
Traditional Aluminum Extrusion Cooling |
Advanced Cooling System |
Improvement Range |
|
Peak Junction Temperature |
112℃ |
89℃ |
-20.5% |
|
Light Decay Rate (1000 hours) |
18% |
5% |
-72.2% |
|
Fan Noise |
52dB (forced air cooling) |
0dB (no fan) |
100% silent |
|
Weight |
8.2kg |
6.5kg |
-20.7% |
Verification of Adaptability to Extreme Environments
◎Desert high-temperature test: After 180 consecutive days of operation in the Dubai desert, the daily junction temperature fluctuation range is controlled at 78-85℃, with no sudden light decay;
◎High-humidity salt spray test: After 3 years of use on roads around the Wenchang Space Launch Site in Hainan, the corrosion depth of the heat dissipation fins is <0.02mm (standard requirement <0.1mm);
◎High-altitude low-pressure test: At an altitude of 5000 meters on the Qinghai-Tibet Plateau, the heat dissipation efficiency only decreases by 7%, far better than the industry average attenuation rate of 15%.

Product Advantages
◎Infrared human body sensing
◎Advanced heat dissipation technology
◎Intelligent lighting
◎Energy saving and emission reduction
◎IP65 protection
◎High-power LED
About Us
|
Address: |
Guoji Industrial Park, Songqiao Town, Gaoyou City, Jiangsu Province, China ; |
|
Tel/WhatsApp: |
+86 18118266199; |
|
Mail: |
hjy@jcledzm.cn |
Hot Tags: solar street light 120w, China solar street light 120w manufacturers, suppliers, factory, solar arena lights, best solar panel outdoor lights, ground solar lights outdoor, solar powered butterfly, free standing solar lights, Municipal Solar Street Lights













