Solar Led Light 100w

Product Introduction

• Low-Power Energy Saving: Equipped with an 180Wp high-efficiency monocrystalline silicon solar panel and 100Ah lithium iron phosphate battery, combined with smart MPPT control and three-level dimming, energy-saving efficiency ≥80%.
• High Color Rendering: Color rendering index Ra≥85, using full-spectrum technology and asymmetric light distribution design to accurately restore colors, with uniform illuminance and anti-glare properties.
• Convenient Installation: Integrated modular structure with patented 卡扣 (snap) brackets supports 30-minute quick installation without trenching or cabling, compatible with 3-10 meter lamp poles.
• Intelligent Operation and Maintenance: Built-in NB-IoT/LoRa modules support remote monitoring and OTA upgrades, reducing fault response time from 24 hours to 2 hours.
• Environmental Adaptability: IP65 protection rating, operating in -40°C~+65°C wide temperature range, anodized + fluorocarbon paint for corrosion resistance, suitable for various harsh environments.

Low-Power Energy Saving Technology System

• High-Efficiency Solar Power Supply System

The Solar LED Light 100W is equipped with an 180Wp monocrystalline silicon solar module using N-type TOPCon (Tunneling Oxide Passivated Contact) technology, with a laboratory conversion efficiency exceeding 26.5% and mass-produced module efficiency ≥24.5%.

The system includes a smart MPPT (Maximum Power Point Tracking) controller with a conversion efficiency ≥99.5%, 5% higher than traditional PWM controllers, ensuring maximum solar energy utilization.

• 2.2 Low-Power LED Light Source Technology

Chip-Level Energy Efficiency Breakthrough: Uses Lumileds LUXEON 3535 LED chips with a single-chip luminous efficiency ≥160lm/W. The 100W model has a luminous flux of 16,000lm, saving 37.5% energy compared to traditional 100W high-pressure sodium lamps (luminous efficiency 100lm/W).

Intelligent Dimming Strategy: Built-in microwave radar sensor supports three-level dimming (100%→50%→10%), automatically reducing power at night when no one is present. Combined with light-sensitive automatic switching, the comprehensive energy-saving efficiency ≥80%.

Optimized Heat Dissipation Design: The lamp body is made of 6063-T5 aluminum alloy by die-casting, with a fin-type heat dissipation structure and graphene thermal conductive coating, thermal resistance ≤2.5K/W, ensuring LED junction temperature is controlled within 85°C and extending light source lifespan to 80,000 hours.

High Color Rendering Optical System

• Full-Spectrum Technology Architecture

Color Rendering Performance Parameters: Color rendering index Ra≥85, R9 (saturated red restoration) ≥60, a 21.4% improvement over traditional LED street lamps (Ra≤70), authentically restoring colors of traffic signs, vegetation, etc., enhancing nighttime visibility.

Spectrum Optimization Scheme: Uses 450nm blue light chips + three-primary-color phosphor combination to achieve continuous spectrum output, color tolerance ≤3SDCM, color temperature adjustable range 2700K (warm white)-6500K (cold white), adapting to different scene requirements.

• Optical Light Distribution Design

Asymmetric Batwing Light Distribution: Optimizes the beam angle to 120°×60° through freeform surface lenses, road surface illuminance uniformity U0≥0.5, glare index TI≤15, compliant with CIE S008/E:2001 standards.

Anti-Glare Technology: The lens surface uses micro-structured diffusion treatment, with upward light ratio (ULOR) ≤5%, avoiding light pollution and ensuring visual comfort for pedestrians and drivers.

Wire-Free Installation Architecture

• Modular Integrated Design

Integrated Structure: Solar panel, LED light source, battery, and controller are integrated into the lamp body, weighing only 18kg, supporting single-person installation.

Quick Installation Interface: Uses patented snap brackets, compatible with 3-10 meter lamp poles, completed within 30 minutes, improving construction efficiency by 80% compared to traditional street lamps, no need to damage roads or excavate cable trenches.

• Intelligent Operation and Maintenance System

Wireless Communication Module: Built-in NB-IoT/LoRa modules support remote monitoring of luminaire status (battery level, light intensity, fault alarms), reducing operation and maintenance response time from 24 hours to 2 hours.

OTA Upgrade Function: Can update dimming strategies and firmware versions through the cloud platform to adapt to lighting needs in different seasons and time periods.

Product Advantages

• Low-power energy-saving lighting
• high-color-rendering LED street lamps
• wire-free solar lights
• intelligent dimming systems
• IP65-protected luminaires
• off-grid lighting solutions

About Us

Hot Tags: solar led light 100w, China solar led light 100w manufacturers, suppliers, factory, Led Street Light Waterproof, Solar Led 50w, Led Road Lamp, Solar Led Lights for Street, led light bar, led power