Product Introduction
◎Advantages of LED beads: The 100-watt solar street light adopts 200 3030 high-luminous-efficiency LED beads with a luminous efficiency of ≥160lm/W and a color rendering index of ≥80. Combined with batwing lenses, it achieves uniform lighting. The intelligent dimming strategy can save 68% energy. In actual scenarios, the brightness is 30% higher than that of traditional high-pressure sodium lamps with lower glare.
◎Monocrystalline silicon cell technology: Monocrystalline silicon cells are prepared by the Czochralski method. The orderly arrangement of atoms enables their photoelectric conversion efficiency to reach 21%-23% (15% higher than polycrystalline silicon). Their temperature coefficient (-0.34%/℃), low-light response, and anti-attenuation performance are significantly better than polycrystalline silicon, with laboratory efficiency exceeding 26.81%.
◎Comparison between monocrystalline silicon and polycrystalline silicon: Monocrystalline silicon leads comprehensively in commercial efficiency, temperature adaptability, attenuation rate, and full-life-cycle economy. Although its cost is 10% higher, the 10-year net income is 43% higher than that of the polycrystalline silicon scheme, with an investment payback period of only 4.2 years.

High-Density LED Bead Array
Bead selection and optical design
◎High luminous efficiency: The luminous flux of a single bead reaches 120-150lm, 50% higher than that of traditional 5630 beads (80-100lm). The overall luminous efficiency of the lamp is ≥160lm/W, and the output brightness under 100-watt power reaches 16,000 lumens, equivalent to a 250-watt high-pressure sodium lamp.
◎High color rendering: The color rendering index (CRI) is ≥80, close to natural light (CRI=100), which can clearly restore the colors of road signs (such as red no-parking lines and yellow warning signs). It is 300% higher than low-pressure sodium lamps (CRI=20), significantly reducing the rate of nighttime traffic accidents.
◎Precise light distribution: Adopting batwing lenses (beam angle 120°×60°), optimized through Monte Carlo ray-tracing simulation, it achieves uniform road illuminance (average illuminance ≥30lx, uniformity 0.7), reducing dark areas by 50% compared with traditional street lights (uniformity 0.4-0.5).

Bead quantity and heat dissipation design
◎Bead layout: The whole lamp integrates 200 3030 LED beads, divided into 10 groups in parallel (20 beads per group). A single group failure does not affect the overall lighting, and the failure rate is 80% lower than that of designs with fewer beads.
◎An aluminum substrate + red copper heat pipe composite heat dissipation structure is adopted, with a thermal resistance of ≤0.5℃/W. The junction temperature of the beads is controlled below 65℃ (when the ambient temperature is 40℃), and the service life is 3 times longer than that of ordinary aluminum substrates (thermal resistance 1.2℃/W) (passing 60,000 hours of LM-80 test).
Intelligent dimming strategy
◎Time control + light control dual modes: Automatically turn on/off according to sunrise and sunset times, and reduce the brightness to 50% (8,000 lumens) in the late night (23:00-5:00), saving 40% energy compared with full-power operation throughout the day.
◎Human flow sensing dimming: Detect pedestrians/vehicles through microwave radar. When there are no moving targets within 50 meters, the brightness automatically drops to 30% (4,800 lumens), further saving 28% energy.

Monocrystalline Silicon Solar Cells
Technical principle of monocrystalline silicon cells
Monocrystalline silicon cells are prepared by the Czochralski method (CZ method), with their atoms arranged in a periodically ordered structure. Compared with polycrystalline silicon with disordered arrangement, they have the following advantages:
◎Long minority carrier lifetime: The minority carrier lifetime of monocrystalline silicon reaches 1ms (only 0.1ms for polycrystalline silicon), reducing the recombination probability of electron-hole pairs by 90% and achieving higher photoelectric conversion efficiency.
◎Uniform resistivity: The resistivity deviation of monocrystalline silicon is ≤10% (≥30% for polycrystalline silicon), reducing efficiency attenuation caused by local heating.
◎Anti-PID effect: Through silicon nitride (SiNx) passivation layer treatment, monocrystalline silicon cells have a power attenuation of ≤2% (≥5% for polycrystalline silicon) after 1,000 hours of testing in an environment of -1000V high voltage and 85℃/85%RH.
Performance comparison between monocrystalline silicon and polycrystalline silicon cells
|
Parameter |
Monocrystalline Silicon Cells |
Polycrystalline Silicon Cells |
|
Laboratory efficiency |
26.81% (recorded by LONGi in 2023) |
22.3% (conventional products) |
|
Commercial efficiency |
21%-23% |
18%-20% |
|
Temperature coefficient |
-0.34%/℃ (output decreases slowly with temperature rise) |
-0.45%/℃ |
|
Low-light response |
Maintains 85% efficiency at 200lux illuminance |
Only 70% efficiency at 200lux illuminance |
|
Attenuation rate |
≤2% in the first year, ≤8% in 25 years |
≤3% in the first year, ≤15% in 25 years |
|
Cost |
0.35 yuan/W (10% higher than polycrystalline silicon) |
0.32 yuan/W |
Product Advantages
◎High-density LED beads
◎Monocrystalline silicon cells
◎Photoelectric conversion efficiency
◎Full-life-cycle economy
◎Intelligent dimming
◎MPPT charging
About Us
|
Address: |
Guoji Industrial Park, Songqiao Town, Gaoyou City, Jiangsu Province, China ; |
|
Tel/WhatsApp: |
+86 18118266199; |
|
Mail: |
hjy@jcledzm.cn |
Hot Tags: 100 watt solar led street light, China 100 watt solar led street light manufacturers, suppliers, factory, rgb led lights, led lights for living room, Motion Sensor Solar Street Light, Led Solar Street Light 500w, Led Street Light with Sensor, led street light













