200 Watt Led Street Light
video
200 Watt Led Street Light

200 Watt Led Street Light

1.Pole anti-corrosion, 6063-T5 aluminum alloy base material + hot-dip galvanizing + fluorocarbon spraying composite process
2.Infrared sensing technology, dual-element pyroelectric sensor
3.Intelligent dimming strategy, supporting time/sensing dual modes
Send Inquiry
Description

Product Introduction

◎Pole anti-corrosion performance: The 200 Watt LED Street Light adopts a composite process of 6063-T5 aluminum alloy base material + hot-dip galvanizing + fluorocarbon spraying. It passes a 5000-hour salt spray test, with a service life of over 20 years. Its corrosion resistance is 5 times higher than that of traditional carbon steel poles, and its weight is reduced by 66%.

◎Infrared sensing technology: Integrating a Fresnel lens and a dual-element pyroelectric sensor, it achieves a detection distance of 15 meters, a response speed of 0.5 seconds, and a recognition accuracy of 98%. Combined with a time-segmented dimming strategy, the comprehensive energy-saving rate reaches 65%.

◎Intelligent dimming strategy: Supports time/sensing dual modes. It maintains 30% brightness when no one is present, increases to 100% brightness within 0.5 seconds after detecting humans/vehicles, and returns to energy-saving mode after a 30-second delay. It can distinguish between humans and small animals to avoid false triggers.

◎Anti-interference and environmental adaptability: Through temperature compensation, electromagnetic compatibility (IEC 61000-4-6), and IP67 protection design, it ensures stable operation in environments with temperatures ranging from -40℃ to 85℃, high salt spray, and strong electromagnetic fields.

1

 

6063-T5 Aluminum Alloy Hot-Dip Galvanized Pole

The 200 Watt LED Street Light adopts a composite anti-corrosion process of 6063-T5 aluminum alloy base material + hot-dip galvanizing + three-layer fluorocarbon spraying. It passes the ISO 9227 salt spray test for 5000 hours without red rust, with a tensile strength of 310MPa, and its service life is extended by more than 5 times compared with traditional solutions.

 

(1) Base material selection: 6063-T5 aluminum alloy

◎Composition: Al-Mg-Si series alloy (Mg 0.45%-0.9%, Si 0.2%-0.6%), containing trace Cu (0.1%) to improve corrosion resistance;

◎Performance: Density 2.69g/cm³ (carbon steel 7.85g/cm³), weight reduced by 66%; tensile strength 310MPa (Q235 carbon steel 370MPa), meeting the structural requirements of GB/T 13912;

◎Corrosion resistance: Corrosion rate <0.01mm/year in 3.5% NaCl solution (carbon steel >0.5mm/year), adapting to C5-M high corrosion grade environments (ISO 12944 standard).

 

(2) Surface treatment: Hot-dip galvanizing + fluorocarbon spraying

◎Hot-dip galvanized layer: Thickness ≥85μm (national standard ≥65μm), zinc layer uniformity complies with ASTM A123, no missing plating in edge areas;

◎Fluorocarbon coating: Three-layer structure (primer 30μm + topcoat 50μm + clear coat 20μm), PVDF content ≥70%, UV aging resistance (no chalking after 3000 hours of QUV accelerated test);

◎Adhesion: Tested according to GB/T 9286 cross-cut method, grade 0 (no peeling), resistant to sand impact and mechanical friction.

 

Anti-corrosion performance comparison: Aluminum alloy vs carbon steel

Parameter

6063-T5 Aluminum Alloy (Hot-Dip Galvanizing + Fluorocarbon)

Q235 Carbon Steel (Hot-Dip Galvanizing)

Difference Analysis

Salt spray test

5000 hours without red rust (ISO 9227)

Pitting corrosion occurs at 1000 hours

Corrosion resistance improved by 5 times

Corrosion rate

<0.01mm/year (3.5% NaCl solution)

>0.5mm/year

Service life extended by 8-10 years

Impact resistance

Bending strength 310MPa (withstands level 12 typhoon)

Bending strength 370MPa (but strength drops sharply after rusting)

Aluminum alloy has better structural stability

Weight

2.69g/cm³ (6-meter pole weighs 85kg)

7.85g/cm³ (6-meter pole weighs 250kg)

Transportation/installation cost reduced by 66%

Maintenance cycle

20-year maintenance-free

Rust removal and repainting required every 3-5 years

Full life-cycle cost reduced by 70%

 

Infrared Sensing Module

The 200 Watt LED Street Light integrates a Fresnel lens + digital signal processor (DSP), achieving a detection distance of 15 meters, a response speed of 0.5 seconds, and a recognition accuracy of 98%. Combined with a time-segmented dimming strategy, the comprehensive energy-saving rate reaches 65%.

Intelligent dimming strategy: On-demand lighting and maximum energy efficiency

◎Time mode:

Automatically turns on/off according to sunrise/sunset time, supporting time-segmented brightness adjustment (e.g., reducing to 30% after 22:00);

◎Sensing mode:

Unoccupied state: Maintains 30% brightness (6000 lumens);

Human/vehicle detection: Increases to 100% brightness (20000 lumens) within 0.5 seconds, returns to energy-saving mode after a 30-second delay;

Multi-target tracking: Distinguishes between humans and small animals (such as cats and dogs) through DSP algorithm to avoid false triggers.

Energy efficiency improvement: The comprehensive dimming strategy reduces the average daily power consumption from 1.2kWh in the traditional fixed mode to 0.42kWh, with an energy-saving rate of 65%.

2

 

Product Advantages

◎6063-T5 aluminum alloy

◎Hot-dip galvanizing

◎Infrared sensing

◎Intelligent dimming

◎Anti-corrosion pole

◎Full life-cycle cost

 

About Us

Address:

Guoji Industrial Park, Songqiao Town, Gaoyou City, Jiangsu Province, China ;

Tel/WhatsApp:

+86 18118266199;

Mail:

hjy@jcledzm.cn

Hot Tags: 200 watt led street light, China 200 watt led street light manufacturers, suppliers, factory, Solar Led Street Light All in One, 1000 Watt Street Light, led lens, 150w Street Light, Street Solar Light with Battery, 40w Led Street Light

Send Inquiry

(0/10)

clearall